Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Blanco Fence Installation: The Orlando Owner’s Guide
We install and replace Blanco fence components throughout Orlando, with most full fence installations running $3,500 – $9,000 depending on linear footage, gate hardware, and whether we’re working with Blanco’s aluminum or vinyl lines. Most Orlando homeowners call us when a section has blown loose in a storm, a gate post has started leaning, or the latch no longer lines up after a few years of Central Florida heat and shifting soil. You’ll get a written price before any work starts, and the number we hand you is the number on the invoice.
A quick note for clarity: Penhallow Remodeling Orlando is an independent service provider. We’re not affiliated with Blanco, but we work with their fence systems regularly and understand how their components fit together and what tends to fail first in Florida’s climate.
Which Blanco Models This Applies To
Blanco’s residential fence line in the U.S. market breaks down into two main families: their aluminum ornamental fencing and their vinyl privacy and semi-privacy systems. The aluminum line uses a modular post-and-panel design with pickets that slide into pre-punched rails, while the vinyl line relies on routed posts and tongue-and-groove panel assembly. The compatibility gotcha we see most often: Blanco aluminum fence panels are not interchangeable with big-box store aluminum panels. The post dimensions and rail brackets differ by a quarter inch in places, and forcing a generic panel into a Blanco post assembly creates stress points that fail at the bracket within a season.
To identify your exact model, look for the manufacturer sticker on the inside of the gate post or on the bottom rail of a removable panel section. If the sticker is gone from sun exposure, measure the post dimensions and the picket spacing. Both numbers matter: Blanco uses a 2″ x 2″ post profile on most residential aluminum lines and a 5″ x 5″ post on their heavier privacy vinyl. We stock OEM Blanco components for common series and carry a line of aftermarket equivalents that match Blanco’s rail profile exactly for the cases where OEM lead times run long. For Orlando homeowners, we typically recommend OEM on gate hardware (hinges, latches, self-closing mechanisms) because that’s where failure is most visible and most annoying.
Styles & brands we work with
Signs Your Blanco Fence Installation Is Failing
- Gate post leaning more than a few degrees off plumb. This usually means the concrete footing wasn’t deep enough or water has eroded the soil around it. In sandy Orlando soil, posts set at less than 24 inches deep work loose within two to three wet seasons.
- Panels rattling or flexing in wind. Loose rail brackets or stripped screws at the post connection. Blanco’s aluminum rails use a slide-in channel; once the channel deforms slightly, the whole panel loses rigidity.
- Latch no longer catches or requires lifting the gate to close. Gate sag from a worn hinge or a post that has drifted out of alignment. This is the most common call we get in the College Park area, where older homes have settled and gate geometry has shifted over decades.
- White chalky residue on vinyl panels. Surface oxidation from Central Florida’s UV exposure. This is cosmetic initially, but unchecked, the panel surface gets brittle and cracks at the routed joints.
- Water pooling at the base of the fence line. This points to drainage issues rather than a fence problem, but it accelerates post rot and concrete footing failure if left alone.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
For a Blanco fence installation or full replacement in Orlando, you’re looking at $3,500 – $9,000 installed. The range breaks down by material and scope: aluminum ornamental runs $28 – $45 per linear foot installed, vinyl privacy runs $32 – $55 per linear foot installed. A typical 100-foot backyard fence with one gate lands around $4,200 – $5,800. What moves the number: gate count (each gate adds $400 – $900 with hardware), the amount of old fence we’re removing and hauling, whether the existing posts can be reused or need new footings, and access to the work area.
Every quote includes all parts, concrete for footings, hardware, labor, debris removal, and a written workmanship guarantee. We use stainless steel fasteners on all Orlando installs because galvanized hardware corrodes fast in our humidity. And because this is how we operate under The Kingswell Way, that written price and written guarantee are in your hands before anyone picks up a tool.
DIY or Call Us?
Fence work is generally not dangerous in the same way high-tension springs or electrical panels are, but it’s also not as simple as YouTube makes it look. The safety concern here is less about injury and more about a fence that fails: a gate post set at 18 inches in sandy soil will eventually lean into your neighbor’s yard or swing into your car. What you can safely do is inspect. Check post plumb with a level, test gate swing, look for loose screws or deformed rail channels. What you should not do is pour new footings without knowing your property line, your HOA’s fence rules, or your local wind load requirements. Orlando is in a high-wind region, and fence installations here need to meet Miami-Dade or Florida Building Code standards depending on where exactly you are in the metro. If you’d rather have a crew that carries that code knowledge and the right hardware on the truck, call (850) 427-6454 and we’ll give you the number first, then pick up the tool.
FAQs
Blanco aluminum fence systems typically last 15 – 25 years in Orlando’s climate with minimal maintenance. Vinyl lines run 20 – 30 years if the posts are set correctly and the drainage around the fence line is decent. The limiting factor here is usually the gate hardware and post footings, not the panel material itself. Call (850) 427-6454 and we’ll take a look at what you’ve got and tell you honestly whether it’s worth repairing or replacing.
Yes, in most cases a leaning post can be re-set or reinforced without touching the rest of the fence. We dig out the old footing, re-set the post in fresh concrete at proper depth, and reattach the panels or gate. If the post itself is cracked or corroded at the base, replacement of that single post makes more sense. Either way, the fix is far cheaper than a full installation. We’ll quote both options so you can decide with real numbers in front of you.
A typical 100-foot fence with one gate takes two to three days, including old fence removal, post setting, panel installation, and gate adjustment. Concrete needs a day to cure before we hang the gate and panels, so you’re looking at a minimum of two days on almost any install. We’ll give you a specific arrival window and a completion date in writing before we start.
We keep common Blanco gate hinges, latches, post caps, and rail brackets on our trucks, and we have OEM and aftermarket panel sources with short lead times for the rest. You won’t need to chase down parts yourself; that’s part of what you’re paying us to handle. If you know your model number, we can confirm parts availability before we even schedule the job. Call (850) 427-6454 for a free estimate, and we’ll tell you exactly what we have and what it costs.
We also work with parts and materials from KraftMaid, Cambria, and Silestone on other project types, so if your fence fix turns into a conversation about the rest of the house, we can talk through that too.
Written by Trevor Nash, Owner, Penhallow Remodeling Orlando at Penhallow Remodeling Orlando, serving Orlando and nearby areas.
