Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Belgard Fence Installation: The Orlando Owner’s Guide
Belgard fence installation in Orlando typically runs between $3,500 and $9,000 for a complete residential project, depending on linear footage, panel style, and whether we’re working with new construction or retrofitting existing posts. We stock Belgard-compatible fence panels, posts, and gate hardware locally, and our crew can usually get a full installation done inside a week. Most Orlando homeowners call us after a storm or years of humidity have compromised their existing fence: posts leaning, panels cracked, gate hinges sagging, or the classic Florida problem of concrete footings that were never poured deep enough to begin with.
Here’s the part most people don’t realize until it’s too late: a Belgard fence is only as good as what’s underneath it. The panels themselves are dense, weather-resistant, and built to hold up in Orlando’s climate. The failure point is almost always the installation underneath, from the depth of the post holes to the drainage around the base. We fix that properly the first time.
Which Belgard Models This Applies To
Belgard’s fence line runs through several series that show up regularly in Orlando backyards and side yards. The most common installations we encounter are the Metro series (clean, linear panels with a modern profile), the Bel-Air series (taller privacy panels with a board-on-board look), and the Weston series (mid-century style with alternating vertical and horizontal lines). Each series uses its own post and panel dimensions, so a Metro panel will not drop into a Bel-Air post system without modification. That compatibility gotcha catches a lot of homeowners who buy a panel on clearance and then discover it doesn’t match their existing post spacing.
If you’re trying to identify what you have, look for a small stamp or label embossed on the back face of a panel near the bottom edge, usually inside a corner. It’ll show a series code along with the manufacturing year. If the label’s gone, measure the panel thickness and the distance between post centers: Metro panels run a consistent 6 feet between posts, while Weston panels can span up to 8 feet. For most Orlando homes, we recommend staying with genuine Belgard panels rather than a generic aftermarket panel. The concrete mix and UV stabilizers in Belgard’s material are matched to their own post system, and mixing brands often means the mounting channels don’t align the way they should. We also handle parts from KraftMaid, Cambria, and Silestone when fence work runs alongside other outdoor projects, but for Belgard fence installation specifically, OEM is almost always the smarter call.
Styles & brands we work with
Signs Your Belgard Fence Installation Is Failing
- Posts leaning more than 5 degrees out of plumb. This is almost always a footing problem, not a panel problem. In Orlando’s sandy soil, post holes dug only 18 inches deep will shift within two years. We dig to at least 30 inches and pour concrete footings with a slight crown so water runs away from the post base.
- Gaps opening between panel edges. Belgard panels expand and contract with temperature swings, and Orlando’s daily heat cycles make this worse than inland climates. If you see gaps wider than a quarter inch that don’t close on their own, the mounting channels are likely corroded or the panels were installed too tightly to begin with.
- Gate dragging or refusing to latch. A sagging gate means the hinge posts were undersized or the gate frame wasn’t reinforced. We see this constantly on older Orlando installs where a standard 4×4 post was used for a gate that carries 80 pounds of panel.
- White chalky residue on panel surfaces. That’s efflorescence, a sign that moisture is moving through the concrete panel. By itself it’s cosmetic, but combined with spalling (crumbling edges) it means the panel has absorbed too much Florida humidity and the surface is starting to fail.
- Bottom rails sitting in standing water. Orlando’s rainy season from June through September puts any low-sitting panel edge at risk. If your fence runs through a low spot in the yard, the bottom rails need clearance and drainage, or they’ll crack from freeze-thaw cycles in winter, even mild Florida freezes like the one we got in January 2025.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
For a standard Orlando residential lot, a full Belgard fence replacement runs between $3,500 and $9,000 installed. The range comes down to three things: how many linear feet you’re fencing, which Belgard series you choose, and whether we’re pulling old concrete footings or starting fresh. A smaller side yard with 40 linear feet of Metro panels might land near the bottom of that range. A full backyard perimeter with Bel-Air privacy panels and two gates will push toward the top.
Here’s what that number includes at Penhallow Remodeling Orlando: removal and disposal of the old fence, new concrete footings at the correct depth for Orlando’s soil, genuine Belgard panels and posts, all mounting hardware, gate installation with reinforced hinge posts, and a final walkthrough where we check every post with a level while you watch. You get a written price before any work starts, and that written number is the number on the invoice. No additions, no surprises at the end. Every Belgard fence installation carries our 365-Day Done Right Promise: if something fails inside a year, we come back and fix it at no charge. That’s in writing, alongside the line-item quote.
For a replacement that’s only a few damaged panels rather than a full run, we typically quote that as a panel swap plus any post repairs, usually well under $1,500. Call (850) 427-6454 and we’ll give you a real number before any tools come off the truck.
DIY or Call Us?
Belgard fence panels are heavy and the installation is more nuanced than it looks, but there are a few things an Orlando homeowner can safely check before calling anyone. Look at the post bases: if water pools around them after a rain, that’s a drainage problem you can address by regrading the soil or adding gravel. Check the mounting screws on the panel channels: if they’re loose, you can hand-tighten them. And mark any shifting post with a pencil line on the concrete so you can tell whether it’s actively moving or just settled.
What you shouldn’t do is try to dig out and reset concrete footings yourself, especially in Florida’s summer heat. A full 30-inch post hole in Orlando’s sand and clay means trenching, proper compaction, and often dealing with roots or underground irrigation lines. We’ve fixed enough homeowner attempts to say this plainly: if the post is moving, the fix is underneath it, and that’s a two-person job with the right tools. Trevor Nash will tell you the same thing at the first walkthrough: give you the number first, then pick up the tool. Call (850) 427-6454 and we’ll come take a look.
FAQs
Genuine Belgard panels typically last 20 to 30 years in Orlando when installed with proper footings and drainage. The panels themselves are the strongest part of the system. What shortens the lifespan here is water management: post bases that sit in wet soil will rot or shift long before a panel fails, which is why we spend more time on the hole than the panel.
Yes, and it’s often more cost-effective than a full replacement. If the panels are still solid and only one or two posts have shifted, we can dig out the old footing, reset the post at the correct depth, and reattach the existing panels. If multiple posts are moving or the panels show efflorescence and spalling in several places, replacement starts to make more sense. Call (850) 427-6454 for an honest assessment and a written repair quote.
Most Orlando residential installations take two to three working days from removal of the old fence to final hardware installation. We schedule a defined arrival window and stick to it, and our technicians arrive in uniform and background-checked, so you know precisely who’s in your yard and when. Weather delays can stretch that window during Orlando’s summer afternoon storms, but we’ll tell you the schedule before we start and keep you updated.
We stock the most common Belgard panel sizes and mounting hardware locally, so most replacements don’t wait on shipping. For specialty series or custom panel dimensions, we place the order directly through Belgard’s distribution network with a defined lead time, and we handle the ordering and delivery so you don’t have to coordinate anything. We carry a selection of panel and post inventory on our trucks for standard installations.
Written by Trevor Nash, Owner, Penhallow Remodeling Orlando at Penhallow Remodeling Orlando, serving Orlando and nearby areas.
