Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Barrette Bathroom Remodeling: The Orlando Owner’s Guide
If you have a Barrette bathroom fixture or component that has failed, we stock and install Barrette-compatible replacement parts across Orlando, with full bathroom remodeling jobs typically running $9,000 to $28,000 and minor part replacements starting far lower. Most homeowners call us after noticing a slow leak around the tub drain, a vanity door that no longer closes square, or grout that has started crumbling along the shower floor. We begin every job by identifying the exact Barrette series and model number, then match the replacement to factory tolerances, not whatever is close enough on a shelf.
We are an independent remodeling contractor serving Orlando, not affiliated with Barrette. What that means in practice: we source genuine Barrette parts where they are the right call, and quality aftermarket equivalents where the OEM part has been discontinued or a better material is available. Either way, the part and the labor carry our written 365-Day Done Right Promise. If it fails inside a year, we come back and fix it. No service call, no re-inspection fee.
Key Takeaways:
- Barrette bathroom parts are common in Orlando homes built or remodeled between roughly 2005 and 2020; the brand’s vanity lines, tub surrounds, and shower bases are the most frequent service calls we see.
- Installed replacement costs depend on what failed: a single vanity hinge or drawer slide is under $200 with labor; a full shower base replacement runs $3,000 to $8,500 installed.
- We give you the number first, then pick up the tool. Written price before any work starts, every time.
Which Barrette Models This Applies To
Barrette bathroom products fall into three rough groups, and each has its own compatibility quirks. The vanity and medicine cabinet line is modular; doors, hinges, drawer slides, and shelf pins from one series often, but do not always, fit another. The tub and shower wall system uses interlocking tongue-and-groove panels; if one panel cracks, you can usually replace that panel alone, but only if the wall profile matches the original. The shower bases and tub-shower combos are the trickiest, because the drain center and rough-in dimensions changed between series.
Here is the identification method we use on every Orlando service call. Look for a manufacturer label, usually on the inside of a vanity door, the underside of a medicine cabinet, or the backside of a tub apron. It will list the model number, the series name, and a manufacturing date. If the label is gone, measure the opening or the part itself: vanity drawer slides come in 14-inch, 16-inch, and 18-inch lengths; shower bases are either 30, 32, or 36 inches by 60 inches with a left or right drain. Bring us a photo and the measurements, and we can usually tell you on the phone whether we have the part on the truck.
For Barrette vanities specifically, the OEM hardware is functional but not exceptional; the drawer slides are side-mount ball-bearing units that run about $8 to $15 per pair wholesale. We commonly upgrade to soft-close slides at the customer’s request, which brings the per-drawer cost to $25 to $45 installed and improves the feel of the cabinet immediately. For hinges, the OEM is a standard 35mm euro-style cup hinge; Blum and Salice both make direct-fit replacements that last longer in Florida’s humidity.
Styles & brands we work with
Signs Your Barrette Bathroom Remodeling Is Failing
- Shower base flex or hollow spots underfoot. In Orlando’s humid climate, the original substrate behind and under a Barrette shower base can compact or crumble, especially in slab homes where a small foundation shift transfers up through the base. If it feels springy, the support layer is compromised.
- Vanity doors that will not stay closed or swing open on their own. The self-closing hinge tension wears out, or the door itself has absorbed enough moisture to sag out of square. Either symptom means the hinge is no longer doing the work.
- Tub surround panels separating at the seams. The silicone bead at each tongue-and-groove joint eventually dries and pulls away, particularly along the back long wall where splash is heaviest. Water gets behind the panel and rots the gypsum behind it.
- Drawer slides that stick, scrape, or drop one side lower than the other. The ball-bearing tracks corrode in Florida’s salt-adjacent air, especially in bathrooms near the coast or with poor ventilation. A drawer that needs two hands to open has a slide that is already done.
- Grout at the shower base perimeter cracking or missing in chunks. This is the earliest, most reliable warning sign. The base shifts slightly as the house settles, and rigid grout cannot flex. Once water gets under the base, you are looking at a full removal, not a regrout.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
A full Barrette bathroom remodel in Orlando runs $9,000 to $28,000 depending on the size of the space, whether the tub surround stays or becomes a walk-in shower, and your material choices. A targeted part replacement is far less: $150 to $400 for most vanity hardware and hinge swaps, $800 to $3,000 for a vanity install, $3,000 to $8,500 for a shower replacement, and $3,500 to $10,000 for a tub-to-shower conversion. Every quote we write includes the part cost, the labor, the removal of the failed component, and disposal, with no allowance for surprise change orders at the door.
We also install Barrette-compatible vanities alongside recognized trade brands we work with daily: KraftMaid and Wellborn cabinetry, Cambria and Silestone countertops, Kohler and Moen fixtures. If your Barrette vanity has failed beyond reasonable repair, we can price you a KraftMaid cabinet with the same footprint, and the 365-day guarantee applies the same way.
What typically drives the number up: water damage discovered behind a failed surround or under a shower base, needing new cement board substrate, meaning the moisture-resistant layer behind your tile, which in Orlando we install to a thicker spec than code minimum because of the humidity load in older bungalows. What drives it down: a clean swap of hardware or hinges, or a part we can match while we are already on site.
DIY or Call Us?
Hinge, drawer slide, and shelf pin swaps are squarely in the safe DIY lane for most homeowners. If you can use a screwdriver and a measuring tape, you can replace a Barrette vanity hinge in ten minutes; we are happy to sell you the part and even point you to the right one if you bring in a photo. Where DIY goes sideways is anything involving the shower base, tub surround, or water supply behind the wall. A shower base that flexes means the support underneath has failed; gluing it down harder from above will not fix the problem and can crack the base, turning a $3,000 repair into a full remodel.
Same principle applies to surround seam separation that has been leaking for weeks or months. The panel is cosmetic; the rot behind it is structural. We have opened up shower walls in Orlando’s College Park bungalows and found 1950s-era framing so far gone that it compressed like dry sponge under our fingers. That is not a repair you want to learn on.
If you are uncertain, call (850) 427-6454. We will talk you through what we need to see, and if a service visit makes sense, you get a written price before we touch anything.
FAQs
A Barrette vanity and hardware in an Orlando bathroom typically lasts 10 to 15 years before hinges or slides need attention, while the tub surrounds and shower bases can fail sooner due to Florida humidity and slab movement. Well-ventilated bathrooms that use exhaust fans during and after showers extend the life of every component behind the tile. If you are near the coast, expect hardware corrosion on the earlier end of that range. Call (850) 427-6454 and we can tell you whether yours is worth repairing or replacing.
Some can: hinges, drawer slides, and shelf pins are replaceable parts that we swap without touching the cabinet body, typically for under $300 installed. A failed shower base or a surround that has separated from the wall is not repairable in a way that lasts; the fix is removal and replacement. We will give you the straight answer before any work is scheduled, and the estimate is free.
A hinge or drawer slide replacement takes less than an hour on site in most Orlando homes. A full shower base or tub surround replacement is a two-to-three-day job including removing the failed component, preparing the substrate, installing the new unit, and sealing everything properly. We schedule a defined arrival window for every visit, so you are not waiting around on a half-day that never starts.
We stock the most common Barrette-compatible hardware on the truck: standard 35mm hinges, side-mount drawer slides in 14, 16, and 18-inch lengths, and shelf pins. For less common parts like a specific tub surround panel or shower base, we order through our supplier network and usually have the part in hand within a few business days. You will never be asked to source your own parts on a job we are doing.
If your Barrette bathroom component has failed and you want a written price, not a ballpark, call (850) 427-6454. We will send a technician who arrives in uniform, with a background check on file, and who will give you the number first, then pick up the tool.
Written by Trevor Nash, Owner, Penhallow Remodeling Orlando at Penhallow Remodeling Orlando, serving Orlando and nearby areas.
