Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Atlas Kitchen Remodeling: The Orlando Owner’s Guide
We stock and install Atlas-compatible kitchen remodeling components throughout Orlando, with full kitchen remodels typically running $14,000 to $45,000 depending on cabinet line, countertop material, and layout changes. Most failed parts we see are cabinet hinges, drawer glides, and corner hardware that have simply worn past their useful life in Florida’s humidity. Here’s the plain truth: the Atlas hardware in your kitchen was built to a spec, and once you know which spec, replacing the failed part is usually fast and predictable.
Owners usually discover a problem the same way: a drawer that suddenly won’t close square, a cabinet door that sags half an inch and catches on the frame below it, or a hinge that groans every time you open it. The part itself is rarely expensive. What matters is matching it correctly so you don’t end up replacing the same piece again next year. We’ll cover how to identify what you have, what it costs to fix, and when it’s smarter to swap the part versus address the whole cabinet run.
Which Atlas Models This Applies To
Atlas kitchen cabinets and hardware have been installed in Orlando homes across a few distinct product lines over the years, and the part you need depends on which one is in your kitchen. The most common Atlas cabinet lines we service in the area include their builder-grade framed cabinets (often found in homes built from the early 2000s through the mid-2010s) and a handful of mid-tier frameless lines that show up in newer subdivisions around Lake Nona, Winter Park, and College Park. Each line uses different hinge cup sizes and mounting patterns.
To identify what you have, pull one hinge off the cabinet door. Look for a stamped number on the hinge arm or cup, usually two digits followed by a letter, like “35G” or “107-B.” That stamp tells you the cup diameter and overlay, which is the critical piece of information. A 35mm cup hinge will not fit a door bored for a 26mm cup, and forcing it will split the door panel. If the stamp is gone, measure the hole in the cabinet door with a millimeter ruler. That measurement alone usually narrows it down.
The OEM versus aftermarket decision matters more with Atlas than with some other cabinet brands. Atlas builder-grade hinges were sourced in large batches, and aftermarket replacements from brands like Blum or Salice are often better-built than the original and fit the same cup boring. But the mounting screw pattern varies by generation. We keep a selection of both OEM Atlas hardware and quality aftermarket equivalents on the truck specifically so we’re not guessing at your kitchen’s generation while standing in your doorway.
Styles & brands we work with
Signs Your Atlas Kitchen Remodeling Is Failing
- Cabinet doors won’t close or stay closed. The hinge spring has lost tension, which happens faster in Orlando because salt-laden humidity accelerates metal fatigue on lower-grade steel. You’ll notice one door in a run starts drifting open an inch after you close it.
- Drawers slide rough or catch halfway. The ball bearings in the drawer glide have worn flat on one side, or the nylon roller has developed a flat spot. This is the single most common Atlas hardware failure we replace, especially on lower drawers that carry pots and pans.
- A door hangs visibly lower on one corner. The hinge plate screws have stripped the particleboard they were driven into. This isn’t a hinge failure as much as a cabinet box issue, and the fix usually involves filling and redrilling the bore or using a hinge repair plate.
- The corner of a carousel or lazy susan binds. Atlas corner units used a plastic pivot bearing that degrades in Florida’s heat, especially in kitchens that get direct afternoon sun. Once the bearing collapses, the whole tray drops and scrapes the cabinet floor.
- Adjustment screws won’t hold a setting. If you adjust the door alignment and it drifts again within a week, the hinge’s cam adjuster is stripped. That part is not repairable, only replaceable.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
Here’s what you’re looking at in Orlando for the most common Atlas hardware replacements, parts and labor together:
- Single hinge replacement: $25 – $75 per door, depending on hinge generation and whether the mounting screws need repair
- Drawer glide replacement: $40 – $120 per drawer, depending on glide length and weight rating
- Full cabinet hardware swap (all doors and drawers): $600 – $2,200 for a typical 10×10 kitchen, depending on how many pieces and whether you’re upgrading to soft-close
- Cabinet refacing with new hardware and doors: $4,000 – $13,000
- Full kitchen remodel with Atlas-compatible cabinetry: $14,000 – $45,000
Every replacement includes the part, labor, and cleanup. When we say the price, that’s the price on the invoice. Nothing changes when we show up. You get a written number before any work starts, per the Kingswell Guarantee that every Penhallow project runs on, plus our 365-Day Done Right Promise: if the same part fails inside a year, we come back and fix it at no charge.
DIY or Call Us?
Cabinet hardware is one of those rare home repairs that sounds simple and usually isn’t, because the parts have enough nuance to punish guesswork. But there are things you can safely do before picking up the phone. Check whether the problem is the hinge or the door alignment by opening the problem door and tightening the two screws on the hinge plate with a Philips screwdriver, then rechecking. If the door is still sagging, look at the hinge cup and find the stamp number we mentioned earlier. That number tells us everything. Don’t attempt to bore a new hinge hole or fill stripped screw holes with wood glue and toothpicks. The first one risks splitting the door panel, and the second fails again inside six months because glue and toothpicks have no shear strength.
If the drawer glide is the problem, don’t try to straighten a bent rail. Once a glide rail bends, it’s done. The fix is a new pair. We carry the common Atlas glide lengths on the truck and can usually tell you over the phone whether we have your size. Call (850) 427-6454 and describe what you’re seeing. We’ll tell you straight.
FAQs
In our experience, Atlas builder-grade hinges last 8 to 12 years in Orlando before the spring tension starts failing, and that number drops to 6 to 8 years in kitchens with high humidity or missing range hood ventilation. Soft-close aftermarket hinges from Blum or Salice generally outlast the original hardware by several years. Call (850) 427-6454 if you’re seeing early failures and want us to look at the whole run.
Yes, in most cases. If the hinge itself is still good and the mounting screws have stripped the cabinet box, we typically install a metal hinge repair plate, a thin steel bracket that spans the stripped area and gives the original hinge a solid surface to mount to. It’s a $25 – $50 fix versus a new cabinet door. Call (850) 427-6454 and we’ll tell you whether yours is a candidate.
Replacing every hinge and glide in a standard 10×10 kitchen takes one technician about four to six hours on site. Replacing a single hinge or one drawer glide is usually under an hour. We give you a written arrival window before the job and a written price before the tools come out of the truck.
We stock the most common Atlas hinge generations, cup sizes, and glide lengths on the truck, along with quality aftermarket options that fit the same bores. If your kitchen needs a less common generation, we can usually source it within a few days from our Orlando-area suppliers. Call (850) 427-6454 and we’ll confirm what we have before you even book.
Written by Trevor Nash, Owner, Penhallow Remodeling Orlando at Penhallow Remodeling Orlando, serving Orlando and nearby areas.
